Work at Height Regulations 2005 – UK Legislation and HSE Guidance

Working at height is one of the most significant safety considerations in construction, maintenance and refurbishment. Falls can occur from roofs, scaffolding, exposed floor edges, stairwell openings and other areas where there is a risk of falling to a lower level.

The Work at Height Regulations 2005 establish legal requirements for managing these risks in Great Britain. They require work at height to be properly planned, supervised and carried out by competent people using suitable equipment.

This guide explains the key requirements of UK work at height legislation, the guidance provided by the Health and Safety Executive (HSE), and the role of collective protection measures such as temporary guardrails and edge protection systems.

Official guidance: For detailed information, visit the HSE Work at Height guidance website.

What Are the Work at Height Regulations 2005?

The Work at Height Regulations 2005 are UK health and safety regulations intended to prevent deaths and injuries caused by falls from height.

They place duties on employers, self-employed people where applicable, and those who control work at height.

The Regulations require those responsible for the work to assess the risks and take suitable measures to prevent falls or minimise their consequences.

These duties are particularly relevant to construction activities involving exposed edges, incomplete structures, stairwells, roof work and temporary access arrangements.

The Regulations apply where a person could fall a distance liable to cause personal injury.

What Is Classed as Working at Height?

Under HSE guidance, work at height means working in a place where a person could fall from one level to another and suffer personal injury if suitable precautions were not taken.

Examples include:

  • Working on a roof or elevated working platform
  • Working alongside an exposed floor edge
  • Working near an unprotected stairwell opening
  • Working on scaffolding or a mobile access tower
  • Working near a fragile roof surface
  • Working at ground level beside an excavation or floor opening

Work at height is not limited to working above ground level. A person falling into an excavation or through an opening may also be exposed to a work-at-height hazard.

Is There a Minimum Height for the Regulations to Apply?

No. There is no general two-metre threshold in the Work at Height Regulations 2005.

The determining factor is whether a person could fall a distance liable to cause personal injury.

This means that fall prevention measures may be necessary even where the potential fall distance is relatively small.

The required precautions should be determined through a suitable and sufficient risk assessment.

Who Is Responsible for Work at Height Safety?

Employers and those who control work at height activities have responsibilities under the Regulations.

Depending on the circumstances, these may include contractors, site managers, building owners, facilities managers and other dutyholders.

Those responsible must ensure that work at height is appropriately planned and organised, supervised and carried out by competent people.

They must also ensure that suitable equipment is selected and used, and that relevant risks are assessed and controlled.

Employees have duties to take reasonable care of themselves and others, follow relevant instructions and cooperate with their employer’s safety arrangements.

The HSE Work at Height Hierarchy of Control

The HSE identifies a hierarchy for managing work at height risks.

The priority is to avoid work at height where reasonably practicable. Where it cannot be avoided, measures should be taken to prevent falls. If a fall risk remains, measures should minimise the distance and consequences of a fall.

1. Avoid Working at Height Where Possible

The first consideration should be whether the task can be completed safely without working at height.

For example, some assembly, preparation or maintenance activities may be carried out at ground level before components are lifted into position.

2. Prevent Falls Where Work at Height Cannot Be Avoided

Where work at height is necessary, suitable fall prevention measures should be provided.

Examples include:

  • Temporary edge protection and guardrail systems
  • Properly protected scaffolding
  • Suitable mobile access towers
  • Existing permanent guardrails
  • Other appropriate collective protection equipment

Where appropriate, collective protection should take priority over personal protection because it does not depend on each individual worker taking action to remain protected.

3. Minimise the Consequences of a Fall

Where the risk of falling cannot be eliminated, suitable measures must be considered to minimise the distance and consequences of a fall.

Depending on the application, these may include safety nets, fall arrest equipment and other appropriately designed protective measures.

The correct solution depends on the working environment, the risks identified and the equipment available.

Why Is Collective Fall Protection Important?

Collective fall protection protects multiple people without requiring each worker to take individual action for the protection to be effective.

Temporary guardrails and edge protection systems are examples of collective fall prevention equipment.

When correctly designed, installed and maintained, these systems can create a physical barrier between workers and exposed edges.

This can be particularly valuable on construction sites where several trades may need access to the same working area.

Personal protective equipment, such as a harness and lanyard, can have an important role, but it should not automatically be selected instead of suitable collective protection.

Temporary Edge Protection on Construction Sites

Temporary edge protection is widely used during construction and refurbishment to reduce the risk of falls from exposed edges and openings.

Typical locations include:

  • Upper floor edges before external walls are constructed
  • Stairwells awaiting permanent balustrades
  • Staircases during building construction
  • Roof edges during suitable construction or maintenance operations
  • Floor voids and openings requiring temporary protection

The selection of edge protection should take account of the supporting structure, fixing method, guardrail configuration and intended use.

It is essential that the complete system is suitable for the installation and that the supporting structure can withstand the loads imposed on it.

Temporary Edge Protection Products

Safety Platforms supplies equipment for temporary edge protection applications, including adjustable telescopic guardrails and posts for timber guardrail arrangements.

Explore Temporary Edge Protection Systems

View Telesafe Telescopic Edge Protection

View Temporary Edge Protection Posts

Equipment should always be selected and installed according to its intended application, technical documentation and the relevant site-specific risk assessment.

What Height Should Construction Guardrails Be?

HSE guidance explains that, for construction work, the Work at Height Regulations require a minimum top guardrail height of 950 mm.

The guidance also identifies a maximum vertical gap of 470 mm between the top guardrail and intermediate protection, together with a requirement for suitable and sufficient toeboards.

These legal requirements should be distinguished from the dimensional requirements of product standards.

For example, BS EN 13374:2025 specifies a minimum principal guardrail height of 1,000 mm for temporary edge protection systems covered by that standard.

The 950 mm and 1,000 mm figures therefore relate to different requirements and should not be confused.

A guardrail meeting a particular height requirement is not necessarily a compliant edge protection system. Its design, strength, configuration, fixings and installation must also be appropriate.

What Is BS EN 13374:2025?

BS EN 13374:2025 is a British and European product standard for temporary edge protection systems.

It specifies technical requirements and test methods for systems used during construction and maintenance.

The standard includes three classes of edge protection — Class A, Class B and Class C — intended for different applications and loading conditions.

It also addresses guardrail arrangements, toeboards, structural performance and other technical requirements.

What Is the Difference Between EN 13374 and the Work at Height Regulations?

The distinction is straightforward:

The Work at Height Regulations 2005 establish legal duties for managing work at height risks.

BS EN 13374:2025 specifies technical product requirements and testing methods for temporary edge protection systems.

Compliance with a product standard may help demonstrate the suitability of equipment for a particular application, but it does not replace the need to comply with the Regulations.

Equally, the presence of temporary guardrails does not remove the need for appropriate planning, inspection, supervision and risk assessment.

Risk Assessments for Working at Height

A suitable and sufficient risk assessment is essential before undertaking work at height.

The assessment should identify the hazards associated with the task, the people who may be affected and the measures needed to control the risks.

For temporary edge protection installations, important considerations may include:

  • The height and nature of the potential fall
  • The location and condition of exposed edges
  • The suitability of the supporting structure
  • The type and configuration of edge protection
  • The proposed fixing method
  • The risk of falling tools and materials
  • Access requirements for workers and other trades
  • The installation and removal process
  • Weather conditions and other environmental factors
  • Inspection and maintenance arrangements

The assessment should be reviewed where working conditions change or where new hazards arise.

Inspection and Maintenance of Work at Height Equipment

Equipment used for working at height must be suitable for its intended purpose and maintained in a safe condition.

Appropriate inspections are necessary, with their nature and frequency depending on the equipment, applicable legal requirements and circumstances of use.

For temporary edge protection, checks may include the condition of posts, guardrails, connections, fixings and the supporting structure.

Particular attention should be given to damage, movement, missing components and alterations made during construction.

Temporary edge protection should not be modified or removed without suitable controls being in place.

Inspection and maintenance arrangements should follow applicable legal requirements and the manufacturer’s instructions.

Planning Safe Work Around Stairwells and Floor Openings

Stairwells and floor openings can present significant hazards during construction, particularly before permanent stairs, balustrades and other protective features have been completed.

Protection should be considered during the planning stages rather than after an opening has become exposed.

Suitable temporary edge protection can help create a defined barrier around the hazard while construction activities continue.

The appropriate system will depend on the structure, available fixing points, access requirements and the work being carried out.

Safety Platforms offers temporary edge protection equipment for stairwell and floor-edge applications.

View Our Temporary Edge Protection Range

Official HSE Work at Height Guidance

The Health and Safety Executive provides authoritative guidance to help employers, contractors and other dutyholders understand their responsibilities.

The official HSE Work at Height section includes information on:

  • The Work at Height Regulations 2005
  • Safe planning and organisation of work
  • Selecting suitable work equipment
  • Ladders and stepladders
  • Risk assessments and fall prevention
  • Common questions about working at height

Read the official guidance: HSE – Work at Height

You can also consult the HSE explanation of the law and the HSE work at height FAQs.

Choosing Suitable Fall Prevention Equipment

The most appropriate equipment depends on the task, working conditions and risks identified.

Where temporary guardrails are suitable, contractors should consider the complete edge protection arrangement rather than individual components in isolation.

Safety Platforms supplies a range of construction safety equipment, including temporary edge protection posts and telescopic guardrail systems.

Browse our Temporary Edge Protection products or contact Safety Platforms to discuss your requirements.


Technical information notice: This page provides general information about work at height safety and relevant guidance in Great Britain. It is not legal advice, a substitute for the full legislation or a replacement for a competent site-specific risk assessment. Product suitability and compliance must be established for the intended application. For authoritative information, refer to the Health and Safety Executive and the applicable legislation.